• If you are new to GiantScaleNews.com, please register, introduce yourself, and make yourself at home.

    We're 1st in Giant Scale RC because we've got the best membership on the internet! Take a look around and don't forget to register to get all of the benefits of GSN membership!

    Welcome!

Search results

  1. AKNick

    Scale 20cc DHC-2 "Beaver" Kit Build from Moustache Model Works

    Worked on my fuselage pin stripes. Talk about tedious! Used the pin stripe backing as my spacing guide. Still need to put the large light blue upper stripe on the other side and seal a couple other spots. Basically done covering the fuselage other than graphics.
  2. AKNick

    110" TIMBER Assembly Thread

    Thanks Fellas! The Falcon 23x8 CF luckily didn't touch the water much. There are some small erosion marks... if it were a wood prop that'd be a different story. I've seen what water can do to a float plane with a wood prop!
  3. AKNick

    110" TIMBER Assembly Thread

    Teaser Video Is LIVE!
  4. AKNick

    Scale 20cc DHC-2 "Beaver" Kit Build from Moustache Model Works

    Glued the vertical stab/rudder assembly in place using 30min epoxy. Cleaned excess epoxy with a paper towel soaked in alcohol. It’s nice that MMW has alignment tabs/slots to help put everything on strait. Just had to tape in place for squareness and that’s it. started adding my monokote...
  5. AKNick

    Scale 20cc DHC-2 "Beaver" Kit Build from Moustache Model Works

    I’m going to use “blue mist” for my trim. Also trying out this smart stripe tool.
  6. AKNick

    110" TIMBER Assembly Thread

    Well I did order new elevators for $50 doubting I could repair the elevator well enough to be happy with it... but Alas! I did!
  7. AKNick

    110" TIMBER Assembly Thread

    patience my friend! Takes time! I’ve probably reduced the footage down to 10min.... but with slow motion it’s back up to about 14min ha ha ha I had way too much fun with the wind and the puddle. I’ve been wanting to try some different features with my video editing and I have a lot of good video...
  8. AKNick

    110" TIMBER Assembly Thread

    I've been playing with the footage, I just don't know what to cut out! started with 8 gigs and 18min, Cut it down to 15min. Thinking about making a teaser/highlight video and also the full version.
  9. AKNick

    110" TIMBER Assembly Thread

    Got some sick video, but at the cost of my elevator. It’s repairable. I’m pretty excited about this aerial footage. Had a couple landings with zero ground speed with the wind blowing about 0-12+mph. If I recall correctly, had to crab the plane on short final with losses and gains which led to...
  10. AKNick

    Scale 20cc DHC-2 "Beaver" Kit Build from Moustache Model Works

    Here's my Robart Point Hinge Installation Method Video:
  11. AKNick

    Scale 20cc DHC-2 "Beaver" Kit Build from Moustache Model Works

    Any insight on monocote pinstripes over ultracote covering? Monocote has a light blue that I really want to use, let me know if there is any precautions I need to know.
  12. AKNick

    Scale 20cc DHC-2 "Beaver" Kit Build from Moustache Model Works

    Spent basically my whole day putting two stripes on. Golly getting the right sizing has been tricky. Photos speak for themselves, sure looks more and more like the beaver I want it to look like!
  13. AKNick

    Scale 20cc DHC-2 "Beaver" Kit Build from Moustache Model Works

    Burned out some holes, put everything together for a photo. And put a little covering over the beaver tail gap that was glued together prior.
  14. AKNick

    Scale 20cc DHC-2 "Beaver" Kit Build from Moustache Model Works

    recently tried a sock, and it was hard for me to get used to. I should really attempt it again.
  15. AKNick

    Scale 20cc DHC-2 "Beaver" Kit Build from Moustache Model Works

    Thanks, it’s not perfect and I had to cheat a couple times. My iron is worn out and abused... it’s scratches the covering a bit. Just got a new iron in the mail. Need to bust it out
  16. AKNick

    Scale 20cc DHC-2 "Beaver" Kit Build from Moustache Model Works

    just got the tool last year, been using it wherever I overlap covering to eliminate bubbles.
  17. AKNick

    Scale 20cc DHC-2 "Beaver" Kit Build from Moustache Model Works

    Finished the blue belly. Took a while. Three steps and two covering angles per side... then throw in the fittings. Had to add some patch material to clean up a few lines... it’s cheating but it works.
  18. AKNick

    Scale 1/3 Scale Extra 330L Build.

    FWIW, Alaska has been making it more difficult to transport hazmat over the last two years as well. Seeing that you have Turnigy/HobbyKing batteries - as of last year they wont ship LiPos to me anymore. I used to be able to cheat the system and order from the China warehouse instead of the US...
  19. AKNick

    Scale 20cc DHC-2 "Beaver" Kit Build from Moustache Model Works

    Been taking some time to get my scale livery reference points down. Including the beacon! I was able to find the full scale version and scale it down 1:6.3 to find that a 10mm Red diffused LED is perfect. So I got some on the way. one thing I noticed... my scale lines were not lining up...
  20. AKNick

    110" TIMBER Assembly Thread

    JR America’s went under and JR\Propro was re-emerged with DeForce. They make a great system. @Snoopy1 can tell you about his recent purchase. Lots of other contenders out there. Modern computer radios are pretty amazing. The only thing to keep in mind so the the 40cc twin is a lot of them...
Top