• If you are new to GiantScaleNews.com, please register, introduce yourself, and make yourself at home.

    We're 1st in Giant Scale RC because we've got the best membership on the internet! Take a look around and don't forget to register to get all of the benefits of GSN membership!

    Welcome!

Search results

  1. TonyHallo

    Scale Wendell Hostetler 30% Piper Cherokee Glass Fuselage Build.

    Mounted the cowl on a piece of 1/4"lauan plywood. Need to make 4 latches.
  2. TonyHallo

    Discussion The I’m Going/Went Flying Thread

    Hit -8 today!
  3. TonyHallo

    Scale Mick Reeves 1/3 scale Tiger Moth

    Light is right! You feeling guilty not working on the Cub?
  4. TonyHallo

    Scale Wendell Hostetler 30% Piper Cherokee Glass Fuselage Build.

    Hinge install. This is a slow process. One side of the top half was cut apart on the cut line, need to remove 1/8" of material for the hinge. Tape strips were installed on the top half and mold to act as witness marks. The parts were returned to the mold and taped into position to check the...
  5. TonyHallo

    Sport Racing plane for 3 cylinder Kolm engine.

    After you done building it, then mold it!
  6. TonyHallo

    Scale Wendell Hostetler 30% Piper Cherokee Glass Fuselage Build.

    The revised bottom is complete. I'm happy! Next up hinge the top half.
  7. TonyHallo

    Sport Racing plane for 3 cylinder Kolm engine.

    I use fans on my Roto 85 because they don't want to restart after sitting for a short period after landing. Temps are fine in the air however.
  8. TonyHallo

    Sport Racing plane for 3 cylinder Kolm engine.

    Had a look at the manual, not much there, looks like there's only one temp sensor. I think I would instrument the rear cylinder.
  9. TonyHallo

    Scale Wendell Hostetler 30% Piper Cherokee Glass Fuselage Build.

    The mold modification worked as planned, a couple coats of wax and will lay up a new part. It's not perfect but will make an acceptable part, the defects in the air dam are below the trim line so all is good.
  10. TonyHallo

    Electronic Carburetor/Roto 85 FS Install

    I had to cut a rather large hole in the engine stand used for the Saito FG61 to get the Roto mounted. When I ran the engine it had quite a bit or vibration in the 3000 - 4000 rpm range. Decided to make a stand for the engine and increase the stiffness. It's mounted and ready for testing.
  11. TonyHallo

    The 'What did you do in your workshop tonight?' thread

    Here is the fuel flange for the Super Cub, I would image the J3 is about the same size. I would make it about 7/8" like the photo above.
  12. TonyHallo

    The 'What did you do in your workshop tonight?' thread

  13. TonyHallo

    Scale Wendell Hostetler 30% Piper Cherokee Glass Fuselage Build.

    While researching the number of screws used in the cowl came across this photo of the bottom half of the cowl. After seeing it I just couldn't leave it alone. Works out well because the current requires the removal of the nose wheel to remove the cowl. alone.
  14. TonyHallo

    Scale Mick Reeves 1/3 scale Tiger Moth

    The wing area of the Mick Reeves Tiger Moth seems to be a guarded secret. I found the full scale is 239 square foot, so the 1/3 scale comes in at 3824 square inches, that's a lot of wing! At the advertised weight of 30 pounds, the cubic loading is 3.51which puts it in the glider category.
  15. TonyHallo

    The 'What did you do in your workshop tonight?' thread

    My flying buddy delivers glass for a local company that makes tempered glass, big glass, truck mounted crane for loading, Over 50 years ago toured the PPG tempered glass plant in Ford City PA, the tour was part of an Industrial Engineering course, at any rate a worker put a back window on the...
  16. TonyHallo

    Electronic Carburetor/Roto 85 FS Install

    Yes, welcome back and you will if it is successful, need to make two gasket and it is ready for test run however it's just a tad too cold right now,
  17. TonyHallo

    Sport Racing plane for 3 cylinder Kolm engine.

    What is the engine weight?
  18. TonyHallo

    Scale Mick Reeves 1/3 scale Tiger Moth

    That is a big plane, what's the wing area?
  19. TonyHallo

    Scale Wendell Hostetler 30% Piper Cherokee Glass Fuselage Build.

    Slide the cowl onto the current build fuselage to find the center, aligned the prop spinner center . windshield center support and the vertical fin with a laser level, then marked the center of the cowl so that the cut lines can be laid out. Received two pack of Sig XX hinges in the mail, after...
  20. TonyHallo

    Sport Racing plane for 3 cylinder Kolm engine.

    Let's see a photo of the area.
Top