Search results
-
Scale Mick Reeves 1/3 scale Tiger Moth
Each wing section is approximately 54" x 18"....- dhal22
- Post #81
- Forum: Giant / Scale Scratch and Kit Build Threads
-
Sport Racing plane for 3 cylinder Kolm engine.
30 lbs? :p- dhal22
- Post #143
- Forum: Giant / Scale Scratch and Kit Build Threads
-
Scale Mick Reeves 1/3 scale Tiger Moth
I’m going to pull out a wing plan and double check the ws.- dhal22
- Post #79
- Forum: Giant / Scale Scratch and Kit Build Threads
-
Discussion The I’m Going/Went Flying Thread
Great colors and scheme…- dhal22
- Post #756
- Forum: Giant / Scale RC General Discussions
-
Scale Mick Reeves 1/3 scale Tiger Moth
I ran out of 1/4" spruce so I cut my own. I had some leftover from the Cub kit.- dhal22
- Post #75
- Forum: Giant / Scale Scratch and Kit Build Threads
-
Scale Mick Reeves 1/3 scale Tiger Moth
The fuse builds in 3 sections. Close to gluing up side 1 of section 1. I cut both sides while I was at it.- dhal22
- Post #74
- Forum: Giant / Scale Scratch and Kit Build Threads
-
Scale Mick Reeves 1/3 scale Tiger Moth
And my Perma Grit sanding blocks. I had to dust them off........- dhal22
- Post #73
- Forum: Giant / Scale Scratch and Kit Build Threads
-
Scale Mick Reeves 1/3 scale Tiger Moth
Glue!!! Omg I used glue for the first time in years..........- dhal22
- Post #72
- Forum: Giant / Scale Scratch and Kit Build Threads
-
Scale Mick Reeves 1/3 scale Tiger Moth
Doesn't the full size Tiger Moth have folding wings? :rolleyes:- dhal22
- Post #71
- Forum: Giant / Scale Scratch and Kit Build Threads
-
-
Electronic Carburetor/Roto 85 FS Install
Sleet and rain all day today here, then the cold starts to get serious tomorrow night. At least for Georgia......- dhal22
- Post #21
- Forum: Gas Engines
-
Scale Mick Reeves 1/3 scale Tiger Moth
Not sure. 50"(?) Ws x 18"(?) chord x 4 wings....- dhal22
- Post #67
- Forum: Giant / Scale Scratch and Kit Build Threads
-
The 'What did you do in your workshop tonight?' thread
Probably a Tony question here. I need to make a fake gas cap but not sure about scale size. Thoughts?- dhal22
- Post #12,748
- Forum: Giant / Scale RC General Discussions
-
Scale Mick Reeves 1/3 scale Tiger Moth
I wonder what I’m getting into…. My son stopped in to look at my new project and asked how big. I pulled a tape measure out and showed him 117”. Then I told him it is a biplane. He stared for a few seconds at the tape measure and so I did i…….. This is a big kit.- dhal22
- Post #63
- Forum: Giant / Scale Scratch and Kit Build Threads
-
Scale Mick Reeves 1/3 scale Tiger Moth
Some test fitting tonight.- dhal22
- Post #61
- Forum: Giant / Scale Scratch and Kit Build Threads
-
The 'What did you do in your workshop tonight?' thread
I ordered tempered glass. They put a chamfer around the edges and maybe a slight bevel. I will use the same company again. And I will pay for delivery.- dhal22
- Post #12,746
- Forum: Giant / Scale RC General Discussions
-
Scale Mick Reeves 1/3 scale Tiger Moth
Moving pieces around this evening.......- dhal22
- Post #60
- Forum: Giant / Scale Scratch and Kit Build Threads
-
Scale Mick Reeves 1/3 scale Tiger Moth
Doing some more inventory. What a kit.............- dhal22
- Post #59
- Forum: Giant / Scale Scratch and Kit Build Threads
-
Scale Mick Reeves 1/3 scale Tiger Moth
Imagine, if you will, correctly cut parts, AND some build photos. Why i could shave years off my build. Sooooo many parts were cut incorrectly on my Cub kit..... This kit looks more like an assembly vs a true build thread. My RCAAIR Nelitz Cub kit had many incorrect parts and with only...- dhal22
- Post #58
- Forum: Giant / Scale Scratch and Kit Build Threads
-
The 'What did you do in your workshop tonight?' thread
Cleared a work table today. I ordered table top glass a few years ago and the glass company strongly recommended a full table sized piece of glass. Unfortunately they were correct. This Tiger Moth fuse is 8+ feet long. I will eat my mistake and order a full table sized piece of glass.- dhal22
- Post #12,744
- Forum: Giant / Scale RC General Discussions