-
-
Stevendavis reacted to Snoopy1's post in the thread Scale 112” - Taylorcraft by HeyLuc & Snoopy. with
Like.
Ok just a small update the plane has been moved from the shop to the garage. Battery checked and charged fuel tank check and the motor... -
Stevendavis reacted to TonyHallo's post in the thread Scale Wendell Hostetler 30% Piper Cherokee Glass Fuselage Build. with Like.
No progress on the Cherokee, still finishing up the mods to the Champ. Purchased this 40cc starter kit for an Ephil 40 cc engine that I...
-
Stevendavis replied to the thread Yippee! What the postman brought.Nice!
-
Ok I must thank @pawnshopmike for this. THANK YOU VERY MUCH. I was looking for CA hinges and they were not available anywhere. Mike...
-
Stevendavis reacted to dhal22's post in the thread What did you make with your lathe/mill today? with Like.
Nice table setup.
-
Stevendavis replied to the thread What did you make with your lathe/mill today?.Thanks Mike!
-
Stevendavis reacted to pawnshopmike's post in the thread What did you make with your lathe/mill today? with Like.
Wow looks amazing. Great work brother.
-
Stevendavis replied to the thread What did you make with your lathe/mill today?.Got the rotary table fixture plate finished up!!
-
-
Finished making the fairings, etched and primed. The trim tab is also primed ready for color. Trimmed away the overlapping fabric at...
-
Doing a little work on the Champ to get ready for upcoming contests. Pulled out the static judging sheets from last year's Fall...
-
Necro-Post.... lol My experience was a couple quality control issues (Bad Solder).. but the system works very well... the computer...
-
Ain't that the truth!
-
Dang it, so many hobbies and so little time. Now I want to head to my big toys shop and make chips
-
Stevendavis replied to the thread Mini lathe (and mill) discussion..This is how bad the Vevor chuck was out of the box. I could barely turn the chuck key.
-
-
Stevendavis replied to the thread Mini lathe (and mill) discussion..Glad I could help!
-
I think I would just drill as you go, good chance half the holes will never be used! Just added a 4" diameter disc to my McMaster Carr...
-
More tooling from AliExpress, adjustable VEE block and cutoff and grooving tools, 2mm through 5mm. Took two orders to get the cutoff...
-
Stevendavis replied to the thread Mini lathe (and mill) discussion..Now I have to drill and tap many holes!
-
-
Stevendavis replied to the thread Mini lathe (and mill) discussion..Yep, it's a 6". Here's the first stage done. Once I had the section of material I was going to use faced and trued, I took it over to a...
-
-
Stevendavis replied to the thread Mini lathe (and mill) discussion..Recently picked up a 6 jaw from Vevor. Had to do some work to it right off the bat to make it function properly. Works good now and I...
-
-
Stevendavis replied to the thread Mini lathe (and mill) discussion..Not happy with the quality from Vevor lately. That one you have works great in a vise.
-
Stevendavis replied to the thread Mini lathe (and mill) discussion..Those cutoff tools work great! I still need an angle block.
-
Stevendavis reacted to dhal22's post in the thread Discussion The I’m Going/Went Flying Thread with Like.
Spectacular day for flying. Not hot, not cold, not cool, not warm, no wind and partly cloudy. I had to start worrying about battery...
-
Stevendavis reacted to AKNick's post in the thread Discussion The I’m Going/Went Flying Thread with Like.
Took the TA Horizons Stol X out for its maiden flight along with my pocket radio on ELRS. Everything went great. The plane flies quite...
-
Heck no! It would require complete disassembly to get it in my shop or two olympic weight lifters.
-
-
Loading…
-
Loading…
