• If you are new to GiantScaleNews.com, please register, introduce yourself, and make yourself at home.

    We're 1st in Giant Scale RC because we've got the best membership on the internet! Take a look around and don't forget to register to get all of the benefits of GSN membership!

    Welcome!

Recent content by RC Extreme Power

  1. R

    SPE43 Starting Problems

    All the above plus you could have cracked your spark plug and can not see it. If all fails to solve your problem you need to pull your prop hub and see it is out of line, could have sheared the woodruff key. Milton
  2. R

    after market ignition

    This is the same feed back I get from other customers, I have been selling ignition conversion for 3W-DA and ZDZ for over three years and as I know of no one has had a problem with them. Milton
  3. R

    Useful ignition information

    Need some information on ignitions. What ignition to use. Installing new plug caps. Timing your engine. Checking polarity on sensor. The link below might be useful to you. http://giantscalenews.com/forums/rcextremepower-com.133/ Milton
  4. R

    Timing your engine

    In the link below is two ways to time your engine. Works with RCexl or RCXP and most any ignition that is timed 28-30 degrees before top dead center. http://www.rcextremepower.net/timing.html Milton email tthomp1334@yahoo.com Phone 678 372 7697
  5. R

    Installing new plug caps on 5/8-3/4 hex instructions

    Will add text instructions later .
  6. R

    Installing CM6 Plug caps

    Here are some instructions for installing CM6 plug caps on your ignition. Our RCXP ignition have a smaller plug wire and the wire shielding goes to the inside of the plug cap. Email tthomp1334@yahoo.com Phone 678 372 7697 Milton
  7. R

    What replacement ignition do you need?

    Most all RCexl and RCXP ignitions are the same with close to the same timing curve and will work with most all China made engines and some domestic made engines with magnet on hub set up to be timed at 28-30 degrees before top dead center. Will not work with DA-3W and ZDZ with out a special...
  8. R

    Checking sensor polarity and setting ir right

    I get phone calls from people that there new ignition does not work. I check all ignitions before I ship them so 95% of the time I already know the problem. Engine manufactures use different poles on the magnet to fire the sensor. DA-3W-ZDZ and a couple others use the north pole of the magnet...
  9. R

    New Vendor Support Sub-Forum, RCeXtremePower.com!!

    First a big thanks to GSN for setting this up. Over time I will post some problem solving information that might save people some time when trying to trouble shoot ignition problems. If you have any questions about any ignition product post it and we will see if we can help you work it out...
  10. R

    after market ignition

    ?????? Milton
  11. R

    after market ignition

    PM me what needs to be done. Milton
  12. R

    after market ignition

    I do come here from time to time. My single ignitions are RCAME I put my own labels on them with month and year sold so I can keep track of what I have sold and when sold. Milton
  13. R

    Gas can all done..

    Posted the wrong picture, can't figure out how to change it. That one is with a Miracle pump, had nothing but problems with them. Hope this is the right picture. Milton 17634=11915-2 gallon 6 volt.jpg
  14. R

    Gas can all done..

    We have sold over a hundred of the same pumps in the last 1 1/2 years and as we know of had not had a problem. Here is a picture of the cans we sell with the pumps mounted. Milton 17353=11866-2 gallon 12 volts.jpg
  15. R

    Good prop drill bit

    All way's drill from the back side of prop, That way if the bit runs off a little the back side will still match the prop hub Milton
See more
Top