• If you are new to GiantScaleNews.com, please register, introduce yourself, and make yourself at home.

    We're 1st in Giant Scale RC because we've got the best membership on the internet! Take a look around and don't forget to register to get all of the benefits of GSN membership!

    Welcome!

Search results

  1. gyro

    Eugene Oregon 3D Bash & Monster Fest

    Joe should do a noon demo
  2. gyro

    3DHS 70" Velox

    I use a throttle kill, and when the throttle is not killed, the prop turns just above the minimum required to make it move, so that it doesn't ever stop in flight.
  3. gyro

    74" Edge 540

    There wasn't a manual when I built mine... not sure if they ever made one.
  4. gyro

    74" Edge 540

    They're for your throttle servo, so you can place them wherever you like. Little one is mini size, big one is standard size servo.
  5. gyro

    Extreme Flight 88" Edge -- now with EXP sized horizontal stabs

    I'll take some photos and document my mod of the 104" extra rudder to be removable, as the procedure is the same.
  6. gyro

    New Here? Introduce yourself!

    It is! And I should have my 104 assembled by then!
  7. gyro

    3dhs 92" edge 540 !!!

    Yep, I just shimmed mine. Has held up ok so far
  8. gyro

    3dhs 92" edge 540 !!!

    Yes, I had alignment problems with the cowls on both of the 92 Edges I've owned. Both times the issue was related to poor cowl ring installation and/or alignment at the factory. During a phone call with Noll from 3dhs on a separate topic, I mentioned this issue, and he said, "mine is the same...
  9. gyro

    30cc and 60cc airframes

    The piped DA60s I've seen don't have baffling as the engine usually is exposed to the air through the bottom of the cowl. Matter of fact, you could close the top of the cowl (cover the inlets abeam the prop) so that ALL incoming air passes over the engine, past the pipe, and out the vents on...
  10. gyro

    Easy way to create custom length servo extensions

    Nice tip! And with the small extensions only costing a few $$, this might be similar in cost when outfitting an entire airplane.
  11. gyro

    30cc and 60cc airframes

    Good call. Split cowl is nice, but not necessary, and definitely more difficult for removal and reinstallation.
  12. gyro

    EF Extra 300 104"

    Great advice and technique. I've been pretty happy with the Vaseline in the past, and in retrospect remember the epoxy was starting to get warm a little as I was doing the last few hinges. I think I just ran out of time.
  13. gyro

    3DHS Planes Picture Thread

    Awesome!!!!! Thanks for sharing!
  14. gyro

    St George Utah 3D Bash

    Do it!
  15. gyro

    Dad_Roman

    Thanks for looking into it, no rush!
  16. gyro

    Dad_Roman

    Have you seen the one that has all the words on their own sign, with a different guy holding each one?
  17. gyro

    Twisted Hobbys Owner's Thread!!

    Did you get the th power system for the beaver? What servos is everyone running in their beavers?
  18. gyro

    Dad_Roman

    That one is one of my FAVORITES! 3DMIKE / NJSwede a little help here?!?!
  19. gyro

    The 3DRCForums -Discuss Anything Thread-

    The one with Daniel will be published next week. You can subscribe to our podcast feed at: www.3drcforums.com/rss.xml
  20. gyro

    The 3DRCForums -Discuss Anything Thread-

    Just wanted to send out a big thank you to @danielph for spending a LONG time both talking RC, and recording an awesome podcast with me. This episode is one I definitely can't wait to release!
Top