• If you are new to GiantScaleNews.com, please register, introduce yourself, and make yourself at home.

    We're 1st in Giant Scale RC because we've got the best membership on the internet! Take a look around and don't forget to register to get all of the benefits of GSN membership!

    Welcome!

The 'What did you do in your workshop tonight?' thread

AKNick

640cc Uber Pimp
A bit more progress tonight. Laser cut some hex washers for the little screws to bite into. Had a thought that sometimes the circular ones break loose and maybe with the added hexagon sides they’d hold their ground better. Dunno but that what went through my head at 3am.
IMG_4775.jpeg

CA’d the panel in place. Boy that’s good visual progress. Was quite satisfying to put that in place with all the notches.

IMG_4776.jpeg

Tomorrow maybe I’ll splice the other parts in and reinforce before adding the square balsa pieces.
 

AKNick

640cc Uber Pimp
Spliced in on side of the repair.
IMG_4779.jpeg

This one caught me off guard. Sounds like replacing the cuffs and wheel pants is an up to six month ordeal. Going to try and see if I can find any else where. They’ve been repaired once already.
IMG_4777.jpeg
 

AKNick

640cc Uber Pimp
Finally got around to some sanding…Decided to leave a note for future me.

IMG_4850.jpegIMG_4851.jpeg

I had a good excuse for the setback because my RAM radiator decided to spring a leak so I spent my weekend replacing that along with my rear brakes and an oil change I was about to do anyways. It’s always somthin!

IMG_4829.jpeg
 

Snoopy1

640cc Uber Pimp

AKNick

640cc Uber Pimp
It is so cold up there you do not need a radiator.
Well it does go through the heater core so I like that!! It was 26F last week and now it's 42F! My recent radiator trauma got me thinking... I've never done my wifes car and it now has 135k on it... I bought the fluid today lol!
 

Snoopy1

640cc Uber Pimp
Need some advice. What I need is what would you be inclined to change or tweak to help with this problem.
The engine is a 3W-42. The engine is difficult to start, but once it is running it idles properly and flies great, high speed great and pulls Good through big loops basically once it is running it runs great.
ok this is what it is like trying to start.
1. it chocks good close the choke flit 3 to 5 times and it starts and dies. Chock closed and throttle closed.
2. will flip the prop 5 to 8 times and it will start and run for a split second. Throttle open 2 to 3 clicks.
3. keep flipping and it keeps trying to start but quits after 1/2 to 1 second Of running. Throttle still open 2 to 3 clicks.
4. Closed the choke again and flipped till it kicked again. Open choke and open throttle 5 klicks.
5. after flipping for a while it keeps starting and then eventually keeps running.
Ok what do I do to make this engine start better or Easier. Your suggestions and help are welcome And appreciated.
 

AKNick

640cc Uber Pimp
Need some advice. What I need is what would you be inclined to change or tweak to help with this problem.
The engine is a 3W-42. The engine is difficult to start, but once it is running it idles properly and flies great, high speed great and pulls Good through big loops basically once it is running it runs great.
ok this is what it is like trying to start.
1. it chocks good close the choke flit 3 to 5 times and it starts and dies. Chock closed and throttle closed.
2. will flip the prop 5 to 8 times and it will start and run for a split second. Throttle open 2 to 3 clicks.
3. keep flipping and it keeps trying to start but quits after 1/2 to 1 second Of running. Throttle still open 2 to 3 clicks.
4. Closed the choke again and flipped till it kicked again. Open choke and open throttle 5 klicks.
5. after flipping for a while it keeps starting and then eventually keeps running.
Ok what do I do to make this engine start better or Easier. Your suggestions and help are welcome And appreciated.
Initial thought is it that it’s a bit lean on the LSN, they always harder to start when they are on the lean side.
If you’re flipping after it’s choked with the Ignition off, I tend to wiggle the prop off the compression a few times and then turn the Ignition on and flip it to start.
On my 35cc DA, might have even been Mike that suggested choke on/throttle WOT/ign off and that helped my initial starts tremendously… just have to be very methodical and cautions with that method. But it worked very well.
 

Snoopy1

640cc Uber Pimp
Initial thought is it that it’s a bit lean on the LSN, they always harder to start when they are on the lean side.
If you’re flipping after it’s choked with the Ignition off, I tend to wiggle the prop off the compression a few times and then turn the Ignition on and flip it to start.
On my 35cc DA, might have even been Mike that suggested choke on/throttle WOT/ign off and that helped my initial starts tremendously… just have to be very methodical and cautions with that method. But it worked very well.
Thanks for the reply, I am hoping it is a little lean on LSN easy to change and check.
 
Top